For a big impact with a small investment for your bathroom or kitchen, consider changing the faucet! It’s a super easy, relatively low-cost improvement, that in some cases, can totally change the look and feel of your space!Continue reading →
It is Time to Replace Your Faucet
Is it time to replace a faucet in your kitchen or bathroom? While some people may think that it is a challenge replacing a leaky or outdated faucet isn’t always as difficult as you may think. You can easily tackle the project with a basin wrench and a few other common tools. Usually, it will only take about an hour. The same steps will apply if you are installing a new faucet onto a new sink.
Removing the old faucet:
Step 1: Turn off the water supply. The valves are typically under the sink. If not, turn the water off at the main valve. Then turn on the faucet to relieve any water pressure left in the lines.
Step 2: Disconnect the supply lines from the faucet. Use a basin wrench if you can’t reach the connections with your hands.
Step 3: Disconnect the lift rod, and then remove the nuts from under the faucet.
Remove the drain:
Step 4: Unscrew the slip nut on the P-trap. Put a bucket underneath to catch water in the trap.
Step 5: Disconnect the drain flange from the tailpiece. It should unscrew.
Step 6: Clean the old drain and faucet holes. Mineral spirits can help to remove old silicone sealant.
Install the New Faucet:
Step 7: Follow the manufacturer’s directions for specific installation instructions. Most installations begin with installing the gasket on the bottom of the faucet. Some require sealant of plumber’s putty. Then put the faucet through the mounting holes in the sink and tighten the mounting nuts.
Step 8: Not all faucets come preassembled, so you may have to attach the handles. It is relatively easy. Slip the guide ring onto the bottom of the handle, position it on the faucet base, and secure with the setscrew. A setscrew is a tiny screw on the underside of the handle. Your faucet probably came with a hex wrench to tighten it.
Step 9: Next move onto the drain. Screw the nut all the way down on the drain body and push the gasket over it. Some gaskets are threaded and simply screw into place.
Step 10: Apply just a little bit of silicone under the flange. Position the drain body on the bottom of the sink- making sure the pivot hole is facing the back- and screw the flange on from the top side.
Step 11: Underneath, tighten the nut and gasket. On the top, use mineral spirits to clean up excess silicone.
Step 12: Install the drain rod next. Unscrew the pivot nut on the drain body, insert the horizontal rod through the hole in the stopper, and replace the nut. Push the horizontal rod down and secure the lift rod to the strap with the screw. Test the lift rod.
Step 13: Reconnect the supply lines to the faucet. If your sink is already in place, use a basin wrench to reach the faucet shanks.
Step 14: Flush the faucet by removing the aerator. This gets rid of debris or sediment in the faucet. Some faucets include a handy little tool to unscrew the aerator. When you’re done, keep it inside your vanity or with the rest of your tools. Turn on the hot and cold water for about a minute. Check all of the connections for leaks and retighten if necessary. Screw the aerator back on and you are done.
If you are in the market for a new kitchen or bathroom faucet, contact us at Plumbtile and we can help you pick from many options of quality kitchen and bathroom faucets for your home.
Replacing Your Faucet In Your Guest Bathroom
Expecting guests over anytime soon? There’s no better time to give your guest a bath makeover, and a new faucet is a perfect place to start. Surprisingly, it’s simpler than you think. From start to finish, it can be completed in one afternoon. You’ll spend more time shopping for the perfect fixture than actually installing it.
DIY Installing Your New Bathroom Fixtures
Finding the perfect new bathroom fixtures is only half the battle, the next step is getting your old hardware out and installing the new hardware to complete your updated look.
How-To: Install a new faucet.
When you replace your faucet, be sure to choose a high quality faucet with brass fittings as to make sure longevity is guaranteed. Many manufacturers have warranties for their fixtures, so check with them before you order.
PlumbTile features some of the top brand name faucet manufacturers. So stop by Plumbtile first to pick out your new faucet to compliment your bathroom. Plumbtile.com stocks the widest array of contemporary and traditional faucet and tap designs.